DRV8835 Dual 1.2A Motor Driver Shield for Arduino

This motor driver shield and its corresponding Arduino library make it easy to control a pair of bidirectional, brushed DC motors with an Arduino or compatible board, such as the A-Star 32U4 Prime. The board features Texas Instruments’ DRV8835 dual H-bridge motor driver IC, which allows it to operate from 1.5 V to 11 V and makes it particularly well suited for driving small, low-voltage motors. The shield can deliver a continuous 1.2 A per channel and tolerate peak currents up to 1.5 A per channel for a few seconds, and the channels can be optionally configured to run in parallel to deliver twice the current to a single motor. The shield ships fully populated with its SMD components, including the DRV8835 driver and a FET for reverse battery protection; header pins for interfacing with an Arduino and terminal blocks for connecting motors and power are included but are not soldered in.

2511-003

Quick Spec

  • Motor driver: DRV8835
  • Motor channels: 2
  • Minimum operating voltage: 1.5V (The DRV8835 itself has a minimum motor supply voltage of 0 V, but the board's reverse-voltage protection circuit limits the minimum to 1.5 V.)
  • Maximum operating voltage: 11V
  • Continuous output current per channel: 1.2A (typical results with 100% duty cycle at room temperature)
  • Peak output current per channel: 1.5A
  • Continuous paralleled output current: 2.4A (typical results with 100% duty cycle at room temperature)
  • Maximum PWM frequency: 250kHz
  • Reverse voltage protection

Resources

Shipping List

  • 1 X DRV8835 Dual Motor Driver Shield for Arduino
  • 1 X Connector Set


Dual 1.2A Motor Driver Shield for Arduino

  • Brand: Pololu Electronics
  • Product Code: 2511
  • Stock

    Warehouse Stock Status Location
    Centurion In Stock G18 + I7-03
    Stellenbosch In Stock A0048
  • R125.00 (Inc Tax: R143.75)


Related Products

Stepper Motor 0.5Nm NEMA17 1.8 deg/step

Stepper Motor 0.5Nm NEMA17 1.8 deg/step

Stepper Motor 0.5Nm - Nema17 - 1.8deg/step This hybrid stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1.7 A at 3.8V, allowing for a holding torque of 0.5NM (67 oz-in or..

R220.00 (Inc Tax: R253.00)

Stepper Motor 0.5Nm NEMA17 0.9 deg/step

Stepper Motor 0.5Nm NEMA17 0.9 deg/step

Stepper Motor, NEMA17, Torque 0.5NM 0.9 deg/step Where most stepper motors offers a 1.8deg/step the 42BYGHM809 offers 0.9 deg/step. Product Video Quick Spec 0.5Nm (48N.cm) - 4 Wire ..

R258.00 (Inc Tax: R296.70)

Stepper Motor  2Nm - NEMA23

Stepper Motor 2Nm - NEMA23

Stepper Motor 2Nm - NEMA23 This high-torque hybrid stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 3A at 8.4 V, allowing for a holding torque of 2N. The motor has four ..

R595.00 (Inc Tax: R684.25)

Dual Motor Driver for Raspberry Pi 2/3

Dual Motor Driver for Raspberry Pi 2/3

Dual Motor Driver for Raspberry Pi 2/3 This compact expansion board plugs directly into the GPIO header on a Raspberry Pi B+ and provides an easy and low-cost solution for driving a pair of small b..

R135.00 (Inc Tax: R155.25)

Tags: drv8835, dual, arduino, a-star, 32u4, dual h-bridge, h-bridge