SparkFun Qwiic Pro Micro - USB C
The SparkFun Qwiic Pro Micro is a revision of the original Pro Micro and is, overall, functionally the same as the previous version. The board is the same size as the original Pro Micro but SparkFun have added a few additional features by shrinking down some components on the board such as a reset button, Qwiic connector, USB-C, and castellated pads. Think the Pro Mini except with an ATmega32U4 on board and full USB functionality.
This tiny little board does all of the Arduino tricks that you're familiar with: nine channels of 10-bit ADC, five PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 5V and 16MHz, this board will remind you a lot of your other favorite Arduino-compatible boards. There is a voltage regulator on board so it can accept voltage up to 6VDC. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC.
The benefit of the reset button is to quickly reset the board or place it into bootloader mode without the need to take out a piece of jumper wire. The USB micro-b connector has been replaced with the USB type C connector. The through-hole pads have castellated edges for each pin to add a lower profile in your projects should you decide to build it into another assembly during production. Finally, a Qwiic connector is populated on the bottom of the board to easily add Qwiic enabled I2C devices to your projects.
Product Video
Quick Spec
- ATmega32U4 running at 5V/16MHz
- AP2112 3.3V Voltage Regulator
- Supported under Arduino IDE v1.0.1+
- On-Board USB-C connector for programming
- PTH Pads w/ Castellated Edges
- 9x 10-bit ADC pins
- 12x Digital I/Os (5 are PWM capable)
- Hardware Serial Connections: UART (i.e. Rx and Tx), Qwiic Connector for I2C, SPI
- Weight: 3g
Resources
- Product Page
- Product Wiki
- Schematic
- Board Layout
- ATmega32U4 Firmware NotesM
- ATmega32U4 Datasheet
- Arduino Comparison Guide
- GitHub
Shipping List
- 1 x SparkFun Qwiic Pro Micro - USB C
SparkFun Qwiic Pro Micro - USB C
- Brand: Sparkfun
- Product Code: DEV-15795
- Weight: 0.004kg
- Product Status : Active
Stock
| Warehouse | Stock Status | Location |
|---|---|---|
| Centurion | Limited Stock | FF328 |
| Stellenbosch | Limited Stock | X0030 |
| Bulk Location | No Stock |
We ship free of charge between branches to complete your order.
-
R499.00 (Inc Tax: R573.85)
Related Products
Pro Micro 32U4 Board - 5V 16Mhz - Arduino Bootloader
Pro Micro 32U4 Board - 5V 16Mhz - Arduino Bootloader This tiny little board use the same 32u4 microcontroller as the Arduino Leonardo. The 32u4 is running at 16MHz and 5V. There is a voltage regula..
R189.00 (Inc Tax: R217.35)
QDUINO Mini - Arduino® Compatible Dev Board
QDUINO Mini - Arduino® Compatible Dev Board The Qduino Mini is a tiny, Arduino® compatible board with a battery connector and charger built-in as well as a fuel gauge that can tell you when to charge..
R455.00 (Inc Tax: R523.25)
SparkFun RedBoard Edge
SparkFun RedBoard Edge The SparkFun RedBoard Edge is a nifty little rework of the SparkFun RedBoard designed to be panel mounted in your custom project enclosure to allow for an easy way to make a cl..
R250.00 (Inc Tax: R287.50)
SparkFun RedBoard Turbo SAMD21 + Qwiic
SparkFun RedBoard Turbo SAMD21 + Qwiic If you’re ready to step up your Arduino game from older 8-bit/16MHz microcontrollers, the SparkFun RedBoard Turbo is a formidable alternative. At its heart, the..
R420.00 (Inc Tax: R483.00)
Tags: sparkfun, qwiic, pro, micro, promicro, usb c, usbc, typec, microcontroller, atmega, 32u4, atmega32u4