MKS 3D Printer Board - MEGA + RAMP 1.4

  • Product Code: MKS-GEN14
  • Stock

    Warehouse Stock Status Location
    Centurion In Stock X315
    Stellenbosch In Stock G51 + Y0064
  • R890.00 (price excl. VAT)


MKS 3D Printer Board - MEGA + RAMP 1.4

The MKS Gen V1.4 printer motherboard control board combines and improves the assets solution of the RAMPS 1.4 and Arduino Mega 2560 board on a fantastic single board. The MKS Gen V1.4 printer motherboard control board is an optimal 3D printer controller solution for your 3D printer.

Key features of the MKS Gen V1.4 board:

  • Integrate 2560 and ramps1.4 in a board, to solve thecomplicated interfaces and broken problem of Ramps1.4 combination.
  • Replaceable motor driver, support 4988 driver and 8825 driver.
  • Circuit board using high-quality 4-layer board, and specially dealing with thermal optimization; ramps is a 2-layer board.
  • Using high-quality MOSFET tube, with better heat dissipation.
  • Using a dedicated power chip to support 12V-24V power input, to solve the problem of Ramps voltage converted into chip heating.
  • To accept 24V input, hot bed current can be reduced to 1/4 under the same system power, effectively solve the heating problem of hot bed MOS tube.
  • Firmware can use open-source firmware Marlin, and its configuration is exactly the same as ramps1.4, which can directly replace Ramps1.4.
  • Can directly connect to Ramps1.4,2004LCD control board and 12864LCD control board.
  • Set aside the motor pulse and direction output port, convenient to facilitate external high current to connect external high current (such as 2A, 5A) motor drive circuit.
  • Reserve the Servos, AUX-1, AUX-2 interfaces on Ramps1.4, providing three 5V output, three 12V output interface.
  • This board is an upgrade part of the MKS Gen V1.2 board, improving the performance of power protection and USB communication stability.

Quick Spec

  • Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware
  • Firmware can use the same configuration as ramps1.4
  • Easy DISPLAY + SD-CARD connector,RepRapDiscount SmartController compatible pin header on board
  • All extra pins broken out the same as ramps1.4(AUX-1,AUX-2,AUX-3,Servos1)
  • 3x temperature ADC connectors for thermistors
  • up to 5 motor driver with easy micro stepping setup (micro switches
  • 4x PWM capable power mosfet outputs with voltage selector for MainPower.(Bed,Extruder0,Extruder1, Fans)
  • 4 layers PCB, optimize heat dissipation.
  • 6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
  • 3* 5V output, 3* 12V-24V output interface.
  • Recoverable fuse for short-circuit protection

Board Layout

MKS_GEN14_004

Pinout

11_zps6hlb1szn

Resources

Shipping List

  • 1 X MKS 3D Printer Board - MEGA + RAMP 1.4
  • 1 X USB Cable
  • 1 X JST 4 Pin Wire Kit


Tags: mks, 3d, printer, board, mega, ramp, 1.4, diy, cnc

Also Bought

NEO M8N Mini GPS Module

NEO M8N Mini GPS Module

NEO M8N Mini GPS Module The ATGM336H-5N module is a small family of high performance BDS/GNSS constellation positioning and navigation modules. This series of products are in a micro module, fourth g..

R178.00

Stepper Motor Bracket, NEMA17

Stepper Motor Bracket, NEMA17

Stepper Motor Bracket, NEMA17 You have a stepper motor, but you need to attach it to your CNC project, eh? Not so easy if you don't have a stepper motor mount just like this fine one one here! This..

R79.00

Stepper Motor Bracket, NEMA23

Stepper Motor Bracket, NEMA23

Stepper Motor Bracket, NEMA23 This coated steel mounting bracket provides a simple means of attaching a NEMA-23 sized stepper motor to a flat surface. It has two sets of mounting holes, so it can b..

R128.00

Filament Drive Block for Extruder  1.75mm

Filament Drive Block for Extruder 1.75mm

Quick Specs 10.8mm diameter 12mm height 38 teeth 5mm bore for nema17 stepper motor Shipping List 1 x Filament Drive Block for Extruder 1.75mm ..

R150.00

3D Printer Graphic Display for Ramps

3D Printer Graphic Display for Ramps

3D Printer Graphic Display for Ramps This Smart Controller contains a SD-Card reader, a rotary encoder and a 128x64 LCD display. You can easily connect it to your Ramps board using the "smart adapter..

R350.00