Stepper Motors & Driver Boards
Name (A - Z)
Name (Z - A)
Price (Low > High)
Price (High > Low)
Model (A - Z)
Model (Z - A)
BTS7960 High Power H-Bridge motor driver 43A
The Motor Driver 43A BTS7960 uses an H-bridge driver module that composed by Infineon power drive chip, with overheating and overcurrent protection. Dou..
(Inc Tax: R355.35)
Coupler Shaft Flexible 5mm x 8mm
These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they are not perfectly..
(Inc Tax: R79.35)
DC Brush Motor 6V
This is the 130-size DC motor used in the larger Pololu plastic gearmotors (228:1 offset, 120:1 offset, 200:1 90-degree, and 120:1 90-degree). It has a recommended operating volta..
(Inc Tax: R17.25)
Dual Motor Controller 1.2A per Channel
This breakout board uses the powerful Texas DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an op..
(Inc Tax: R166.75)
Dual Motor Driver 14A
If you are looking to drive two high-power motors through one compact unit, these dual VNH2SP30 motor driver carriers are perfect for you. With these boards, it’s easy to get ..
(Inc Tax: R1,035.00)
Dual motor shield 3A for Arduino
This motor driver shield and its corresponding Arduino library make it easy to control two bidirectional, brushed DC motors with an Arduino or Arduino clone. The bo..
(Inc Tax: R589.95)
Intelligent Motor Controller with Feedback 12A
The powerful Pololu JRK 12V12 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-lev..
(Inc Tax: R1,834.25)
Jrk 21v3 USB Motor controller with Feedback
The jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog vo..
(Inc Tax: R929.20)
L293D Driver IC - DIP
L293D is a dual H-bridge motor driver integrated circuit (IC). Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current ..
(Inc Tax: R17.25)
Linear Bearings 12mm
This linear ball bearing is sort of the opposite of the radial ball bearings you may be familiar with. Its intended to slide along an 8mm linear shaft, rather than rotate aroun..
(Inc Tax: R66.70)
Linear Bearing 6mm - LM6LUU
If you are making a CNC router, mill or lathe requiring precise linear motion, this LM6LUU bearing can be used to attach a motion carriage onto a railing without adding to..
(Inc Tax: R28.75)
LM8U - Linear Bearing 8mm (2 Pack)
This linear ball bearing is sort of the opposite of the radial ball bearings you may be familiar with. Its intended to slide along an 8mm linear shaft, rather tha..
(Inc Tax: R46.00)
Metal Gear Motor 73:1
The 20D mm line of brushed DC gearmotors are available in three different gear ratios, all of which have the same dimensions except for the length of the gearbox. The gearmoto..
(Inc Tax: R287.50)
Metal Gearmotor 75:1 with 48 CPR Encoder
This cylindrical, 2.62" x 0.98" x 0.98" gearmotor uses a brushed DC motor with extra-strong magnets and a 74.83:1 metal gearbox to deliver a lot of power in..
(Inc Tax: R618.70)
Micro Maestro 6-channel USB Servo Controller
The Micro Maestro is a second-generation USB servo controller. The board supports three control methods — USB for direct connection to a PC, TTL serial ..
(Inc Tax: R319.70)
Mini Maestro 24-channel USB Servo Controller
The 24-channel Mini Maestro 24 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripti..
(Inc Tax: R945.30)
N20 Motor + Wheel Kit
This Micro Motor wheel set is especially designed for education market. These tiny brushed DC gearmotors are intended for use at 6 V, though in general, these kinds of motors..
(Inc Tax: R112.70)
Motor Controller Board, Dual Channel, Serial Control
This small, inexpensive motor controller allows variable speed and direction control of two small, brushed DC motors using a simple serial inter..
(Inc Tax: R345.00)
NEMA 17 0.65Nm Dual Shaft Stepper Motor
Stepper motor can be used in such areas as industrial transmission control, powder packaging machine, CD-ROM reader, winding machine, printing machine, cutting..
(Inc Tax: R372.60)
NEMA 23 1.2Nm Dual Shaft Stepper Motor
Stepper motor can be used in such areas as industrial transmission control, powder packaging machine, CD-ROM reader, winding machine, printing machine, cuttin..
(Inc Tax: R483.00)
Pillow Block 6.35mm 1/4" Bore
The pillow block bearing mounts attach to the outside of a channel and can be used as simple hinges. These bearing mounts have a width of 1.32”, a thickness of 0.25”, ..
(Inc Tax: R170.20)
Pololu Motor Controller 5-30V @ 25A
The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the abil..
(Inc Tax: R1,385.75)
Sanyo Pancake Stepper Motor
This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution) and a holding torque of 1 kg-cm (14 oz-in). Each phase draws 1 A at 4.5 V. ..
(Inc Tax: R799.25)
Servo Controller - Serial
The Pololu micro serial servo controller (SSC) is a very compact solution for controlling up to eigh radio control (RC) servos from a computer or microcontroller. The con..
(Inc Tax: R356.50)
Servo Controller 12 Channel - USB/Serial
The 12-channel Mini Maestro 12 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting c..
(Inc Tax: R517.50)
Servo Controller, 16 Channel, I2C Interface
The PCA9685 is a 16 Channel servo controller that can be controlled via I2C. With the PCS9685 you do not need to continuously send it signal tying ..
(Inc Tax: R79.35)
Solenoid 12V Travel 10mm
Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. This smaller solenoid is designed to work directly with 12V which..
(Inc Tax: R151.80)
SparkFun 3A Stepper Driver (8-45V)
The SparkFun AutoDriver board is based on the STMicro L6470 dSPIN stepper motor driver. This powerful chip allows you to control a stepper motor with a voltage from..
(Inc Tax: R573.85)
Stepper Controller USB 1.5A (2A MAX)
The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpo..
(Inc Tax: R511.75)
Stepper motor + slider 90mm
DC 4-9V Drive Stepper Motor Screw With Nut Slider 2 Phase 4 Wire. Our Pololu 1182 Stepper driver will be a good match.
Motor Type: 2 phase 4 wire..
(Inc Tax: R241.50)
Stepper Motor, 3NM, NEMA23
Our 3N.m Bipolar Stepper motor is from the very famous Wantai Motor. Wantai have supplied us over 10 years with quality stepper motors. The motor has a 1.8° step angle (2..
(Inc Tax: R1,029.25)
Stepper Motor 30NM - NEMA 42
This is the Big Daddy in our stepper motor range delivering a mammoth 30NM holding torque. This stepper motor is suitable for high end industrial CNC applications. The ..
(Inc Tax: R5,037.00)
Stepper Motor, NEMA34, Holding Torque 7.7Nm
These powerful stepper motors can deliver 7.7Nm holding torque and is suitable for high end industrial CNC applications. The DQ860MA is good choice when se..
(Inc Tax: R1,983.75)
Stepper Motor 8.5NM
Just Motion produce one of the finest NEMA34 high-torque stepper motors, producing very low vibration at low speeds with very good torque.
(Inc Tax: R1,597.35)
Stepper Motor Breakout Module
This stepper motor breakout module has an on-board DIP switch, so you can easily adjust the drive segments as you require. Terminal power connector for easy drive power ..
(Inc Tax: R103.50)
Stepper motor nema 14, 1.8 Deg , 0.8A
This hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 400 mA at 10 V, allowing for a holding torque of 1 kg-cm (14 o..
(Inc Tax: R224.25)
Stepper Motor Unipolar 5V 0.3kg.cm
Perfect Stepper Motor to learn about Stepper motors and Arduino Interfacing. The ULT2003 chip is perfect to drive this stepper motor from 5V source.
(Inc Tax: R90.85)
Stepper Motor, 1NM, NEMA23 (Now with 2m cable)
The Wantai 57BYGH402 is a high-torque 1NM stepper motor with a 1.8° step angle.
The motor has four color-coded wires and can be controlled with any ..
(Inc Tax: R448.50)
Stepper Motor, Pancake, 0.2NM 1A - Height 16mm
This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 2.2 kg-cm (30 oz-in), and e..
(Inc Tax: R1,367.35)
Tiny Planetary Gearmotor 26:1
These tiny brushed DC gearmotors have a diameter of just 6 mm and weigh just over a gram, which makes them great actuators for miniature robots and very small mechanis..
(Inc Tax: R172.50)
VNH3SP30 Motor Driver Carrier MD01B
This module is a compact breakout board for ST’s high-power VNH2SP30 or VNH3SP30 motor driver IC, each of which is a fully integrated H-bridge that can be used for..
(Inc Tax: R937.25)
VNH5019 Motor Driver Carrier
This module is a compact breakout board for ST’s high-power VNH5019 motor driver IC, a fully integrated H-bridge that can be used for bidirectional speed control of a s..
(Inc Tax: R458.85)
CNC 6 Axis Opto Isolated Parallel Interface Breakout Board + Cable
Easy to use opto-isolated breakout board, for use with CNC routers controlled by Mach3 or EMC. All parallel pins made available th..
(Inc Tax: R242.65)
Wave Nema 17 Stepper 0.45Nm
A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor has a rated curr..
(Inc Tax: R241.50)
XHC Mach 3 USB Controller - 3 Axiz - 5th Generation
XHC produce produce one of the most advance Mach 3 CNC controllers on the market and can produce step pulse frequencies of up to 2Mhz. These cont..
(Inc Tax: R3,782.35)
Stepper Motor, 1.8N.cm, NEMA8 1.8 deg/step
This small NEMA 8-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 600 mA at 3.9 V, allowing for a holding ..
(Inc Tax: R332.35)
Stepper Motor Driver 2A, High Current - Pololu Original
The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pino..
(Inc Tax: R135.70)
Stepper Motor 0.5Nm - Nema17 - 1.8deg/step
This hybrid stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1.7 A at 3.8V, allowing for a holding torque of 0.5NM (67 oz-in or..
(Inc Tax: R204.70)
Stepper Motor Driver 2A (with integrated Voltage Regulators)
This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection..
(Inc Tax: R308.20)
Stepper Motor, NEMA17, Torque 0.5NM 0.9 deg/step
Where most stepper motors offers a 1.8deg/step the 42BYGHM809 offers 0.9 deg/step.
0.5Nm (48N.cm) - 4 Wire
(Inc Tax: R396.75)
Stepper Motor Driver 1.8Amp( 3 Amp Peak)
This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step..
(Inc Tax: R217.35)
Stepper Motor Driver 4.2A - Original
The DQ542MA stepper driver from Wantai Motors has a proven track record and very reliable. It is a more expensive that our TB6600 entry level driver, but the DQ..
(Inc Tax: R718.75)
Wantai Stepper Motor Driver 8A
The DQ860MA is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper..
(Inc Tax: R1,367.35)
Showing 1 to 53 of 53 (1 Pages)