Helium Atom to Pi Adapter*** PLEASE NOTE LIMITED STOCK ***
The Helium Atom to Raspberry Pi Adapter is an easy-to-use HAT-like board equipped with a NRF24LO1 port, Atom socket and RGB-status LED. Also..
Photon Stackable Header - 12 Pin
These stackable headers are made to work with the Particle Photon and Photon ProtoShield boards. Each header adds a great deal of connectivity to your next Photon pro..
QDUINO Mini - Arduino® Compatible Dev Board
The Qduino Mini is a tiny, Arduino® compatible board with a battery connector and charger built-in as well as a fuel gauge that can tell you when to charge..
Qwiic MUX Breakout - 8 Channel TCA9548A
The Qwiic Mux Breakout enables communication with multiple I2C devices that have the same address that makes it simple to interface with. The Qwiic Mux also ha..
Qwiic RFID ID-XXLA
The Qwiic RFID ID-XXLA is a simple board that pairs with and comes in a kit with, the ID-12LA and three RFID 125kHz cards to get you started integrating an I2C RFID solution into y..
Qwiic SparkFun Distance Sensor
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long rang..
Qwiic SparkFun VR IMU Breakout - BNO080
The Qwiic SparkFun VR IMU Breakout is powered by Bosch’s BNO080, a combination triple-axis accelerometer/gyro/magnetometer SiP, packaged with a 32-bit ARM Cort..
Qwiic SparkX RF - LoRa Enabled 866-915MHZ
The Qwiic RF is a packet radio system that’s designed for sending short packets of sensor data from one Qwiic bus to another. Messages sent by one Qwiic RF a..
Qwiic Starter Kit
The Qwiic Starter Kit was designed to allow users to get started with Arduino without the need for soldering or breadboarding. Hooking up a handful of inputs and outputs to an Ardui..
SparkFun Basic Flashlight Solder Kit
This Flashlight Soldering Kit is an easy to assemble soldering kit designed to help teach the basics of through hole soldering and circuit design. This kit requir..
SparkFun Configurable OpAmp Board - TSH82
The SparkFun TSH82 Configurable OpAmp Board was designed to give you the best combination of performance and flexibility that we could achieve by giving you ..
SparkFun Gator:Bit V2.0
The SparkFun gator:bit v2.0 is an all-in-one “carrier” board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pi..
SparkFun IR Array - 110 Deg Qwiic
The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this..
SparkFun Photon Battery Shield
The SparkFun Photon Battery Shield provides you with an easy way to power your Photon module with a Lithium Polymer (LiPo) battery. Not only can the Battery Shield powe..
SparkFun Photon IMU Shield
This is the SparkFun Photon IMU Shield, a versatile motion-sensing add-on board for your Photon device. The IMU shield is equipped with an on-board LSM9DS1 system-in-a-chip..
SparkFun Photon ProtoShield
This ProtoShield mates easily with your Photon module and provides a small soldering area and separated power and I2C hook-ups. With the SparkFun Photon ProtoShield you ha..
SparkFun Proto Shield - Bare
The SparkFun Arduino® compatible ProtoShield is a bare PCB with no attached or included parts that lets you customize your own Arduino® compatible shield. The SparkFun Ar..
SparkFun ProtoShield Kit
The SparkFun Arduino® compatible ProtoShield is a bare PCB with no attached or included parts that lets you customize your own Arduino® compatible shield. The SparkFun Arduin..
SparkFun Qwiic HAT for Pi
The SparkFun Qwiic pHAT for Raspberry Pi (based on the original Qwiic Hat) provides you with the quickest and easiest way to enter into SparkFun’s Qwiic ecosystem while stil..
SparkFun Qwiic MP3 Trigger
The Qwiic MP3 Trigger comes with a microB connector and the WT2003S MP3 decoder IC that gives you access to the files on the microSD card. Simply plug in the Qwiic MP3 Trig..
SparkFun Qwiic PCA9615 Differential
The SparkFun Differential I2C Breakout is the fastest and easiest way to extend the range of your I2C communication bus. The breakout uses NXP’s PCA9615 IC, which ..
SparkFun Qwiic Quad Relay
The SparkFun Qwiic Quad Relay is a unique power accessory board that has been designed for switching not one but four high powered devices from your Arduino or another low p..
SparkFun RedBoard Edge
The SparkFun RedBoard Edge is a nifty little rework of the SparkFun RedBoard designed to be panel mounted in your custom project enclosure to allow for an easy way to make a cl..
SparkFun Thing Plus - SAMD51
Is it power you seek? With a 32-bit ARM Cortex-M4F MCU, the SparkFun SAMD51 Thing Plus is one of our most powerful microcontroller boards yet! The SAMD51 Thing Plus provi..
SparkX Humidity Sensor Breakout SHTC3 (Qwiic)
Sensirion’s SHTC3 digital humidity sensor builds on the success of their SHTC1 sensor. The SHTC3 has a broader supply voltage range (1.62V to 3.6V) and h..