• Stepper Motor Driver 1A - Pololu Original

Stepper Motor Driver 1A - Original from Pololu

The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 – 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling).

Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver.

Quick Spec

  • Minimum operating voltage: 8V
  • Maximum operating voltage: 35V
  • Continuous current per phase: 1A
  • Maximum current per phase: 2A
  • Minimum logic voltage: 3V
  • Maximum logic voltage: 5.5V
  • Microstep resolutions: full, 1/2, 1/4, 1/8, and 1/16
  • Reverse voltage protection: N

Features:

  • Simple step and direction control interface
  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
  • Adjustable current control lets you set the maximum current output with a potentiometer
  • Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
  • Short-to-ground and shorted-load protection

Application Circuit

Resources

Shipping List

  • 1 X Original Stepper Motor Driver Board from Pololu Electronics
  • 1 X Header Pins

Stepper Motor Driver 1A - Pololu Original

  • Brand: Pololu Electronics
  • Product Code: 1182
  • Stock

    Warehouse Stock Status Location
    Centurion In Stock P3-04
    Stellenbosch In Stock B0207
  • R82.00 (Inc Tax: R94.30)


Related Products

Stepper Motor Driver 2A - Pololu Original

Stepper Motor Driver 2A - Pololu Original

Stepper Motor Driver 2A, High Current - Pololu Original The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pino..

R117.00 (Inc Tax: R134.55)

Stepper Motor 0.28Nm NEMA17 1.8 deg/step

Stepper Motor 0.28Nm NEMA17 1.8 deg/step

Stepper Motor, Torque 0.28Nm 1.8deg A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor has a max ..

R185.00 (Inc Tax: R212.75)

Stepper Motor Driver 2.5A

Stepper Motor Driver 2.5A

Stepper Motor Driver 1.8Amp( 3 Amp Peak) This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step..

R299.00 (Inc Tax: R343.85)

Stepper Motor, Pancake, 0.2NM

Stepper Motor, Pancake, 0.2NM

Stepper Motor, Pancake, 0.2NM 1A - Height 16mm This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 2.2 kg-cm (30 oz-in), and e..

R1,189.00 (Inc Tax: R1,367.35)

ULN2003 Stepper Driver

ULN2003 Stepper Driver

ULN2003 Stepper Driver Module The ULN2003 Stepper Motor Driver Board use a ULN2003 IC to drive 4-phase (unipolar) 5-wire stepper motors (5v-12v). Using an Arduino makes it very easy to drive these ..

R38.00 (Inc Tax: R43.70)

Stepper motor + slider 90mm

Stepper motor + slider 90mm

Stepper motor + slider 90mm DC 4-9V Drive Stepper Motor Screw With Nut Slider 2 Phase 4 Wire. Our  Pololu 1182 Stepper driver will be a good match. Quick Specs Motor Type :2 phase 4 wir..

R210.00 (Inc Tax: R241.50)

GRBL shield V3 4 Axis

GRBL shield V3 4 Axis

Arduino CNC shield V3 - 4 Axis - GRBL 0.8C Compatible The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control ..

R125.00 (Inc Tax: R143.75)

SparkFun Haptic Motor Driver - DRV2605L

SparkFun Haptic Motor Driver - DRV2605L

SparkFun Haptic Motor Driver - DRV2605L Ready to add some good vibes to your project? Look no further than the SparkFun Haptic Motor Driver. This board breaks out Texas Instruments' DRV2605L Haptic M..

R110.00 (Inc Tax: R126.50)

 CNC shield V2 - 3 Axis - GRBL Compatible

CNC shield V2 - 3 Axis - GRBL Compatible

Arduino CNC shield V2 - 3 Axis - GRBL Compatible The Arduino CNC Shield makes it easy to get your CNC projects up and running in a few hours. It uses opensource firmware on Arduino to control 4 ste..

R95.00 (Inc Tax: R109.25)

Stepper Motor Driver 2.1A

Stepper Motor Driver 2.1A

Stepper Motor Driver 2.1A This breakout board makes it easy to use Toshiba’s TB67S128FTG microstepping bipolar stepper motor driver, which features adjustable current limiting and microstepping down ..

R198.00 (Inc Tax: R227.70)

Tags: pololu, 1182, stepper, controller, driver, arduino