Adafruit MSA301 3 Axis Accelerometer - Qwiic
The MSA301 is a super small and low cost triple-axis accelerometer. To make life easier so you can focus on your important work, Adafruit have taken the M..
Pressure Sensor (Qwiic) - MS5637
MEMs based barometric pressure sensors are quite common these days. The Qwiic Pressure Sensor with the MS5637 shines by being the most sensitive barometric pressure s..
Qwiic Cable - 200mm
This is a 200mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together but can be used for other applications as well. Each Qw..
Qwiic Cable - Breadboard Jumper (4-Pin)
This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup pigtail on the other. This cable ..
Qwiic Cable - Grove Adapter (100mm)
The Qwiic to Grove Adapter Cable allows interoperability between the SparkFun Qwiic Connect System and the I2C based Grove boards from Seeed Studio. Now you can pl..
Qwiic Distance Sensor - RFD77402
The SparkFun Distance Sensor Breakout utilizes the RFD77402 3D ToF (Time of Flight) sensor module from Simblee to give you the most accurate measurements at short ran..
Qwiic Enviro Sensor - BME680
The BME680 from Bosch is a powerful sensor capable of sensing humidity, barometric pressure, temperature and indoor air quality. The BME680 can communicate over SPI or I2..
Do you find yourself wishing that you had just a few more GPIO pins? What if you only need that one more pin? You could add another microcontroller to your project but that increases cost ..
Qwiic Grid Eye IR Array
The GridEYE from Panasonic is a 8 by 8 thermopile array. This means you have an array of 64 pixels each capable of detecting temperature remotely. It’s like having thermal cam..
Qwiic I2S Audio Breakout - MAX98357A
The SparkFun I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signa..
Qwiic JST Connector - SMD - 4-Pin
Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of the Qwiic-based boards and can be used to create your own I2C-based device compatible ..
Qwiic MUX Breakout - 8 Channel TCA9548A
The Qwiic Mux Breakout enables communication with multiple I2C devices that have the same address that makes it simple to interface with. The Qwiic Mux also ha..
Qwiic Non-Contact Thermometer
Have you ever used one of those non-contact temp guns? This is the newest and smallest version of that sensor. Point the MLX90632 at an object and remotely get its tempe..
Qwiic OLED 0.66" 64X48 - Blue on Black
The SparkFun Qwiic Micro OLED Breakout is a Qwiic-enabled version of SparkFuns' popular Micro OLED display! The small monochrome, blue-on-black OLED screen pres..
Qwiic Open Log
The SparkFun Qwiic OpenLog is the smarter and better looking cousin to the extremely popular OpenLog but now we've ported the original serial based interface to I2C! Thanks to the adde..
Qwiic Pressure Sensor - LPS25HB
The LPS25HB is an absolute pressure sensor which means that it has an internal vacuum as a reference. You can use this absolute pressure sensor to inform a drone autop..
Qwiic RFID ID-XXLA
The Qwiic RFID ID-XXLA is a simple board that pairs with and comes in a kit with, the ID-12LA and three RFID 125kHz cards to get you started integrating an I2C RFID solution into y..
Qwiic RTC (Real Time Clock)
The Qwiic RTC from SparkFun is a very unique and exciting Real Time Clock. It is extremely precise (within 3 minutes over a year!), extremely low power (less than 22nA!) a..
Qwiic SparkFun Distance Sensor
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long rang..
Qwiic SparkFun VR IMU Breakout - BNO080
The Qwiic SparkFun VR IMU Breakout is powered by Bosch’s BNO080, a combination triple-axis accelerometer/gyro/magnetometer SiP, packaged with a 32-bit ARM Cort..
Qwiic SparkX RF - LoRa Enabled 915MHZ
The Qwiic RF is a packet radio system that’s designed for sending short packets of sensor data from one Qwiic bus to another. Messages sent by one Qwiic RF are c..
Qwiic Starter Kit
The Qwiic Starter Kit was designed to allow users to get started with Arduino without the need for soldering or breadboarding. Hooking up a handful of inputs and outputs to an Ardui..
Qwiic to Grove Cable
The SparkFun Qwiic system is expanding greatly. But we understand there are other systems out there. The Qwiic to Grove cable allows interoperability between the SparkFun Qwiic s..
Qwiic Triple Axis Accel - MMA8452Q
This breakout board makes it easy to use the tiny MMA8452Q accelerometer communicate over I2C in your project. The MMA8452Q is a smart low-power, three-axis, capaci..
Qwiic UV Sensor - VEML6075Qwiic UV Sensor - VEML6075
The VEML6075 can detect the intensity of UVA (~365nm) and UVB (~330nm) waves. With a quick calculation, those values can be used to generate a sta..
SparkFun Environment Combo Breakout - CCS811/BME280 (Qwiic)
The SparkFun CCS811/BME280 Environmental Combo Breakout takes care of all your atmospheric-quality sensing needs with the popular CCS811 an..
SparkFun GPS Breakout - XA1110 (Qwiic)
The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to SparkFun's Qwiic Connect System. Equipped with the XA1110 GPS ..
SparkFun IR Array - 110 Deg Qwiic
The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this..
SparkFun Lightning Detector - AS3935 (Qwiic)
The SparkFun Qwiic Lightning Detector adds lightning detection to your next weather station to make sure you are aware of any potential hazardous weather ..
SparkFun Qwiic 12 Bit ADC - 4 Channel
The SparkFun Qwiic 12 Bit ADC can provide four channels of I2C controlled ADC input to your Qwiic enabled project. These channels can be used as single-ended inp..
SparkFun Qwiic Adaptor
The SparkFun Qwiic Adapter provides the perfect means to make any old I2C board into a Qwiic-enabled board. This adapter breaks out the I2C pins from the Qwiic connectors to pi..
SparkFun Qwiic Capacitive Touch Slider
This Capacitive Touch Slider is a "Qwiic" and easy way to add capacitive touch to your next project. With the board's built in touch pads, you can immediately s..
SparkFun Qwiic HAT for Pi
The SparkFun Qwiic pHAT for Raspberry Pi (based on the original Qwiic Hat) provides you with the quickest and easiest way to enter into SparkFun’s Qwiic ecosystem while stil..