Stepper Motors & Driver Boards



Refine Search

Product Compare (0)


Bipolar Stepper Motor with Planet Gear Box

Bipolar Stepper Motor with Planet Gear Box

Bipolar Stepper Motor with Planet Gear Box This bipolar stepper motor with planet gear box (gear ratio: 5.18) uses a standard 8mm-diameter D type output shaft, and has a 1.8° step angle (200 steps..

R699.00

Coupler Shaft Flexible 5mm x 8mm

Coupler Shaft Flexible 5mm x 8mm

Flexible Shaft Coupler 5mm x8mm These couplers are made of machined aluminum and have a spiral cut that makes them slightly flexible so they can be fit to two shafts even if they are not perfectly ..

R69.00

DC Brush Motor 6V

DC Brush Motor 6V

DC Brush Motor 6V This is the 130-size DC motor used in the larger Pololu plastic gearmotors (228:1 offset, 120:1 offset, 200:1 90-degree, and 120:1 90-degree). It has a recommended operating volta..

R35.00

Dual Motor Controller 1.2A per Channel

Dual Motor Controller 1.2A per Channel

Dual Motor Controller 1.2A per Channel This breakout board uses the powerful Texas DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an op..

R145.00

Dual motor driver 14A

Dual motor driver 14A

Dual motor driver 14A  If you are looking to drive two high-power motors through one compact unit, these dual VNH2SP30 motor driver carriers are perfect for you. With these boards, it’s easy t..

R900.00

Dual motor shield 3A for Arduino

Dual motor shield 3A for Arduino

Dual motor shield 3A for Arduino This motor driver shield and its corresponding Arduino library make it easy to control two bidirectional, brushed DC motors with an Arduino or Arduino clone. The bo..

R470.00

Intelligent Motor Controller with Feedback 12A

Intelligent Motor Controller with Feedback 12A

Intelligent Motor Controller with Feedback 12A The powerful Pololu JRK 12V12 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-lev..

R1,095.00

Jrk 21v3 USB Motor controller with Feedback

Jrk 21v3 USB Motor controller with Feedback

Jrk 21v3 USB Motor controller with Feedback The jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog vo..

R750.00

Linear Bearing 12UU  (2 Pack)

Linear Bearing 12UU (2 Pack)

Linear Bearings 12mm This linear ball bearing is sort of the opposite of the radial ball bearings you may be familiar with. Its intended to slide along an 8mm linear shaft, rather than rotate aroun..

R58.00

Linear Bearings LM6UU

Linear Bearings LM6UU

This linear ball bearing is sort of the opposite of the radial ball bearings you may be familiar with. Its intended to slide along an 8mm linear shaft, rather than rotate around it. These are very sli..

R25.00

LM8UU - Linear Bearing 8mm ( 2 Pack )

LM8UU - Linear Bearing 8mm ( 2 Pack )

Linear Bearing 8mm (Pack of 2 ) This linear ball bearing is sort of the opposite of the radial ball bearings you may be familiar with. Its intended to slide along an 8mm linear shaft, rather than r..

R40.00

Metal Gear Motor 154:1

Metal Gear Motor 154:1

Metal Gear Motor 154:1 This gearmotor is a brushed DC motor with 154:1 metal gearbox that has the power to deliver both speed and torque. These units have a 4 mm-diameter D-shaped output shaft. Key..

R278.00

Metal Gear Motor 73:1

Metal Gear Motor 73:1

Metal Gear Motor 73:1  The 20D mm line of brushed DC gearmotors are available in three different gear ratios, all of which have the same dimensions except for the length of the gearbox. The ge..

R250.00

Metal Gearmotor 75:1  with 48 CPR Encoder

Metal Gearmotor 75:1 with 48 CPR Encoder

Metal Gearmotor 75:1 with 48 CPR Encoder This cylindrical, 2.62" x 0.98" x 0.98" gearmotor uses a brushed DC motor with extra-strong magnets and a 74.83:1 metal gearbox to deliver a lot of power in..

R510.00

Micro Maestro 6-channel USB Servo Controller

Micro Maestro 6-channel USB Servo Controller

Micro Maestro 6-channel USB Servo Controller The Micro Maestro is a second-generation USB servo controller. The board supports three control methods — USB for direct connection to a PC, TTL serial ..

R310.00

Mini Maestro 24-channel usb servo controller

Mini Maestro 24-channel usb servo controller

Mini Maestro 24-channel usb servo controller The 24-channel Mini Maestro 24 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripti..

R799.00

Motor + Wheel Kit

Motor + Wheel Kit

Motor + Wheel Kit This Micro Motor wheel set is especially designed for education market. These tiny brushed DC gearmotors are intended for use at 6 V, though in general, these kinds of motors can ..

R150.00

Motor Controller Board, Dual Channel, Serial Control

Motor Controller Board, Dual Channel, Serial Control

Motor Controller Board, Dual Channel, Serial Control This small, inexpensive motor controller allows variable speed and direction control of two small, brushed DC motors using a simple serial inter..

R300.00

Pololu Motor Controller 5-30V @ 25A

Pololu Motor Controller 5-30V @ 25A

Pololu Motor Controller 5-30V @ 25A The Pololu Simple Motor Controllers are versatile, general-purpose motor controllers for brushed, DC motors. A wide operating range of up to 5.5–40V and the abil..

R899.00

Sanyo Pancake Stepper Motor

Sanyo Pancake Stepper Motor

This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution) and a holding torque of 1 kg-cm (14 oz-in). Each phase draws 1 A at 4.5 V. The motor has four color-coded wi..

R695.00

Servo Controller - Serial

Servo Controller - Serial

Servo Controller - Serial  The Pololu micro serial servo controller (SSC) is a very compact solution for controlling up to eight radio control (RC) servos from a computer or microcon..

R310.00

Servo Controller 12 Channel - USB/Serial

Servo Controller 12 Channel - USB/Serial

Servo Controller 12 Channel - USB/Serial The 12-channel Mini Maestro 12 raises the performance bar for serial servo controllers with features such as a native USB interface and internal scripting c..

R450.00

Servo Controller, 16 Channel, I2C Interface

Servo Controller, 16 Channel, I2C Interface

Servo Controller, 16 Channel, I2C Interface You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs ..

R290.00

Servo Rotating Base

Servo Rotating Base

Base rotate kit + HS-422 servo The Base Rotate Kit is perfect for rotating a large mass. It can easily support 10lbs of weight. It has five 6mm bearings to reduce the friction. It's injection mold..

R688.00

Solenoid 12V Travel 10mm

Solenoid 12V Travel 10mm

Solenoid 12V Travel 10mm Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 12V which ..

R99.00

Step 8A Kit

Step 8A Kit

Step 8A Kit - 7.7Nm Stepper motor + controller Please contact Henning on Tel 012 6655713 for quick backorders.  What's included in the Kit: 1 x STEP8A Stepper Controller 7.8A  ..

R2,500.00

Stepper motor + slider 90mm

Stepper motor + slider 90mm

Stepper motor + slider 90mm DC 4-9V Drive Stepper Motor Screw With Nut Slider 2 Phase 4 Wire. Our  Pololu 1182 Stepper driver will be a good match. Quick Specs Motor Type :2 phase 4 wir..

R225.00

Stepper Motor 3.0Nm

Stepper Motor 3.0Nm

Stepper Motor, 3NM, NEMA23 This high-torque hybrid stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 3A, allowing for a holding torque of 3N. The motor has four color-co..

R750.00

Stepper Motor 8.5NM

Stepper Motor 8.5NM

Stepper Motor 8.5NM Just Motion produce one of the finest NEMA34 high-torque stepper motors, producing very low vibration at low speeds with very good torque.  Quick Spec Holding Torq..

R1,389.00

Stepper motor nema 14,  1.8 Deg , 0.8A

Stepper motor nema 14, 1.8 Deg , 0.8A

Stepper motor nema 14, 1.8 Deg , 0.8A This hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 400 mA at 10 V, allowing for a holding torque of 1 kg-cm (14 o..

R195.00

Stepper Motor Unipolar 5V 0.3kg.cm

Stepper Motor Unipolar 5V 0.3kg.cm

Stepper Motor Unipolar 5V 0.3kg.cm Perfect Stepper Motor to learn about Stepper motors and Arduino Interfacing. The ULT2003 chip is perfect to drive this stepper motor from 5V source. Quick Spe..

R79.00

Stepper Motor, 1NM, NEMA23

Stepper Motor, 1NM, NEMA23

Stepper Motor, 1NM, NEMA23 - 57BYGH420 The Wantai 57BYGH402 is a high-torque 1NM stepper motor with a 1.8° step angle. The motor has four color-coded wires and can be controlled with any of our mi..

R349.00

Stepper Motor, NEMA08, Holding Torque 1.8N.cm

Stepper Motor, NEMA08, Holding Torque 1.8N.cm

Stepper Motor, 1.8N.cm, NEMA8 This small NEMA 8-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 600 mA at 3.9 V, allowing for a holding torque of 1..

R289.00

Stepper Motor, NEMA34, Holding Torque 7.7Nm

Stepper Motor, NEMA34, Holding Torque 7.7Nm

Stepper Motor, NEMA34, Holding Torque 7.7Nm These powerful stepper motors can deliver 7.7Nm holding torque and is suitable for high end industrial CNC applications. The DQ860MA is good choice when ..

R1,250.00

Stepper Motor, NEMA42, Holding Torque 30Nm

Stepper Motor, NEMA42, Holding Torque 30Nm

Stepper Motor, 30NM, NEMA42 This is the Big Daddy in our stepper motor range delivering a mamoth 30NM holding torque. This stepper motor is suitable for high end industrial CNC applications. The DQ..

R4,380.00

Stepper Motor, Pancake, 0.2NM

Stepper Motor, Pancake, 0.2NM

Stepper Motor, Pancake, 0.2NM 1A - Height 16mm This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 2.2 kg-cm (30 oz-in), and e..

R1,089.00

Stepper Motor, Torque 0.5Nm 0.9deg/step

Stepper Motor, Torque 0.5Nm 0.9deg/step

Stepper Motor, NEMA17, Holding Torque 0.5NM 0.9deg/step >Where most stepper motors offers a 1.8deg/step the 42BYGHM809 offers 0.9 deg/step. 0.5Nm (48N.cm) - 4 Wire  Step Angle (degr..

R258.00

Tiny Planetary Gearmotor 26:1

Tiny Planetary Gearmotor 26:1

Tiny Planetary Gearmotor 26:1 These tiny brushed DC gearmotors have a diameter of just 6 mm and weigh just over a gram, which makes them great actuators for miniature robots and very small mechanis..

R150.00

VNH3SP30 Motor Driver Carrier MD01B

VNH3SP30 Motor Driver Carrier MD01B

VNH3SP30 Motor Driver Carrier MD01B This module is a compact breakout board for ST’s high-power VNH2SP30 or VNH3SP30 motor driver IC, each of which is a fully integrated H-bridge that can be used f..

R815.00

VNH5019 Motor Driver Carrier

VNH5019 Motor Driver Carrier

VNH5019 Motor Driver Carrier This module is a compact breakout board for ST’s high-power VNH5019 motor driver IC, a fully integrated H-bridge that can be used for bidirectional speed control of a s..

R399.00

Wantai 6 Axiz Breakout Board  + Cable

Wantai 6 Axiz Breakout Board + Cable

CNC 6 Axis Opto Isolated Parallel Interface Breakout Board + Cable Easy to use opto-isolated breakout board, for use with CNC routers controlled by Mach3 or EMC. All parallel pins made available th..

R329.00

Stepper Motor Driver 2A - Original Pololu

Stepper Motor Driver 2A - Original Pololu

Stepper Motor Driver 2A, High Current The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface..

R155.00

Stepper Motor Driver 2A + Regulator

Stepper Motor Driver 2A + Regulator

Stepper Motor Driver 2A (with integrated Voltage Regulators) This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protecti..

R268.00

Stepper Motor Driver 2.5A

Stepper Motor Driver 2.5A

Stepper Motor Driver 1.8Amp( 3 Amp Peak) This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 st..

R299.00

Wantai Stepper Motor Driver 4.2A

Wantai Stepper Motor Driver 4.2A

Stepper Motor Driver 4.2A The DQ542MA stepper driver from Wantai Motors has a proven track record and very reliable. It is a more expensive that our TB6600 entry level driver, but the DQ542MA offer..

R679.00

Wantai Stepper Motor Driver 8A

Wantai Stepper Motor Driver 8A

Wantai Stepper Motor Driver 8A Quick Spec Input voltage: 24-80VDC Input current: 6A Output current: 2.8A~7.8A Consumption Consumption:80W; Internal Insurance:10A Working Temperature -..

R1,250.00

Stepper Motor Driver Shied, Dual 0.75A x 2

Stepper Motor Driver Shied, Dual 0.75A x 2

Shield, Dual stepper motor Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling ca..

R200.00

Stepper Motor, 0.5Nm, 1.8 deg, NEMA17

Stepper Motor, 0.5Nm, 1.8 deg, NEMA17

Stepper Motor 0.5Nm - Nema17 - 1.8deg This hybrid stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1.7 A at 3.8V, allowing for a holding torque of 0.5NM (67 oz-in or 4...

R220.00

Showing 1 to 48 of 48 (1 Pages)