MCP23017 16 Bit IO Expander I2C - SMD
Add another 16 pins to your microcontroller using an MCP23017 port expander. The MCP23017 uses two i2c pins (these can be shared with other i2c devices), and in exchange gives you 16 general purpose pins. You can set each of 16 pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any of the inputs change so you don't have to keep polling the chip.
Use this chip from 2.7-5.5V (good for any 3.3V or 5V setup), and you can sink/source up to 20mA from any of the I/O pins so this will work for LEDs and such. Team it up with a high-power MOSFET if you need more juice.
You can set the i2c address by tying the ADDR0-2 pins to power or ground, for up to 8 unique addresses. That means 8 chips can share a single i2c bus.
Quick Spec
- Max Voltage on VDD with respect to VSS: -0.3V to +5.5V
- Total power dissipation: 700mW
- Storage Temperature Range: -65°C to +160°C
- 16-Bit Remote Bidirectional I/O Port: I/O pins default to input
- High-Speed I2C Interface (MCP23017): 100 kHz, 400 kHz, 1.7 Mhz
- Three Hardware Address Pins to Allow Up to Eight Devices On the Bus Configurable Interrupt Output Pins: – Configurable as active-high, active-low or open-drain
- INTA and INTB Can Be Configured to Operate Independently or Together
- Configurable Interrupt Source: – Interrupt-on-change from configured register defaults or pin changes Polarity Inversion Register to Configure the Polarity of the Input Port Data. External Reset Input, Low Standby Current: 1 mA (max.)
- Dimensions: 10.3 x 8 x 1.8mm
- Net Weight: <1g
Pinout

Resources
Shipping List
- 1 x MCP23017 16 Bit IO Expander I2C - SMD
MCP23017 16 Bit IO Expander I2C - SMD
- Brand: Generic
- Product Code: MCP-23017-SMD
- Weight: 0.001kg
- Product Status : Active
Stock
Warehouse | Stock Status | Location |
---|---|---|
Centurion | No Stock | |
Stellenbosch | No Stock |
We ship free of charge between branches to complete your order.
-
R16.00 (Inc Tax: R18.40)
Related Products
I2C 8-Bit I/O Expander
I2C 8-Bit I/O Expander Quick Spec Operating supply voltage 2.5 to 6 V Low standby current consumption of 10 µA maximum I2C-bus to parallel port expander Open-drain interrupt output 8-..
R16.00 (Inc Tax: R18.40)
I2C 16KB EEPROM
I2C 16KB EEPROM The Microchip 24LC16B is a 16 Kbit Electrically Erasable PROM. We’re using a 16kbit EEPROM which is actually 16 384 bits / 8 bits in a byte = 2048 bytes. (2kb..
R12.00 (Inc Tax: R13.80)
16 Bit IO Expander I2C - Dip
16 Bit IO Expander I2C - Dip Quick Spec 16-bit remote bidirectional I/O port High-speed I2C™ interface (MCP23017) High-speed SPI interface (MCP23S17) Three hardware address ..
R25.00 (Inc Tax: R28.75)
PCF8575 I2C IO Expansion Module - 3.3V/5V
PCF8575 I2C IO Expansion Module - 3.3V/5V Have you run out of I/O pins? This great IC allows the user to expand up to 16 I/O using only two I/O for control! The PCF8575C is controlled through an I2..
R46.00 (Inc Tax: R52.90)
PCF8575 - I2C IO Expansion Module
PCF8575 - I2C IO Expansion Module Do you have out I/O pins? This awesome IC allows the user to expand up to 16 I/O with just two I/O for control! The PCF8575C is controlled via an I2C interface and..
R55.00 (Inc Tax: R63.25)
Wave AW9523B I2C to 16 IO Expansion Board
Wave AW9523B I2C to 16 IO Expansion Board The Wave AW9523B I2C to 16 IO Expansion Board is an expansion board that adds 16 I/O's to your controller. It's compatible with the raspberry pi, Arduino a..
R95.00 (Inc Tax: R109.25)
Adafruit Keypad to I2C Qwiic Encoder - TCA8418
Adafruit Keypad to I2C Qwiic Encoder - TCA8418 Introducing the Adafruit Keypad to I2C Qwiic Encoder - TCA8418, a versatile I2C GPIO expander and keypad matrix driver. With 18 I/O pins, 10 columns, ..
R132.00 (Inc Tax: R151.80)