SparkFun Nano Power Timer TPL5110

The SparkFun Nano Power Timer will run while only consuming minimal power (approximately 35nA) and turn your project on after a set amount of time. When you are done polling your sensors, posting data to the web, writing to your logger, or planning world domination, your microcontroller can tell the Nano Power Timer to turn off the power. No more running your microcontroller all day when you only want to read the ambient temperature once per hour.

The TPL5110 delay is configured with the use of resistors. SparkFun have added a six-way DIP switch to select one of the five pre-installed resistors. The sixth switch is attached to a pad to add your own PTH (or SMD) resistor. The delays associated with the pre-installed headers are shown on the bottom of the board for quick setup. Additionally, you can select more than one switch to combine the resistors in parallel (up to 26 options not including the custom resistor), check out the hookup guide for a nice chart as to the total resistance and corresponding delay for each combination.

The Nano Power Timer can handle voltages between 1.8V and 5.5V as well as current up to 1.1A with times from 100ms to two hours (pre-configured settings range from 30s to 2h). You will find a button on the board which will allow you a quick override to the delay so you can turn your project on whenever you like.

Product Video

Quick Spec

  • Supply Voltage: 1.8V to 5.5V
  • Current consumption at 2.5V: 35nA Typical (50nA Max)
  • Selectable Time intervals: 100ms to 7200s (2 hours)
  • Timer Accuracy: 1%

Resources

Shipping List

  • 1 x SparkFun Nano Power Timer TPL5110


SparkFun Nano Power Timer TPL5110

  • Brand: Sparkfun
  • Product Code: PRT-15353
  • Stock

    Warehouse Stock Status Location
    Centurion Out Of Stock
    Stellenbosch In Stock V84
  • R110.00 (Inc Tax: R126.50)


Related Products

NANO Terminal Adapter for Arduino® Nano

NANO Terminal Adapter for Arduino® Nano

NANO Terminal Adapter for Arduino® NANO This is a terminal adapter for the Arduino® NANO. It is made for Arduino® Nano 3.0. This adapter makes it so much easier to hook up the NANO to the outside wor..

R79.00 (Inc Tax: R90.85)

TPL5110 Low Power Timer Breakout

TPL5110 Low Power Timer Breakout

TPL5110 Low Power Timer Breakout The Adafruit TPL5110 Power Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of turning your project on/off..

R110.00 (Inc Tax: R126.50)

Adafruit TPL5111 Low Power Timer Breakout

Adafruit TPL5111 Low Power Timer Breakout

Adafruit TPL5111 Low Power Timer Breakout The Adafruit TPL5111 Reset Enable Timer is a stand-alone breakout that will turn any electronics into low-power electronics. It will take care of enabling &a..

R120.00 (Inc Tax: R138.00)

Keyes NANO 5V 16MHz - FTDI USB Chipset - With Terminal Adapter

Keyes NANO 5V 16MHz - FTDI USB Chipset - With Terminal Adapter

Keyes NANO 5V 16MHz - FTDI USB Chipset - With Terminal Adapter This NANO compatible is a small, complete, and breadboard-friendly board based on the ATmega328 and FTDI USB Chipset. It lacks only a DC..

R179.00 (Inc Tax: R205.85)

Keywish NANO + NRF24L01+ 2.4GHz

Keywish NANO + NRF24L01+ 2.4GHz

Keywish NANO + NRF24L01+ 2.4GHz This NANO compatible is a small, complete, and breadboard-friendly board based on the ATmega328 and CH340 USB to serial, chipset. It lacks only a DC power jack, and ..

R189.00 (Inc Tax: R217.35)

Tags: sparkfun, nano, power, timer, tpl5110