Wave SIM7000G Pi HAT

This is a telecommunication HAT for Raspberry Pi which supports global bands of NB-IoT, Cat-M, and GPRS, as well as GNSS positioning function. Due to its advantages like small size, low delay, and wide coverage, it is the ideal choice for IoT applications such as intelligent instruments, asset tracking, remote monitoring, e-health, and so on.

The main features of the module are:

• Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
• Supports TCP, UDP, PPP, HTTP, FTP, MQTT, SMS, Mail, etc.
• Supports GNSS positioning (GPS, BeiDou, GLONASS)
• Onboard USB interface, to test AT Commands, get GPS positioning data, and so on
• Breakout UART control pins, to connect with host boards like Arduino/STM32
• Onboard voltage translator, 3.3V by default, allows to be switched to 5V via 0Ω resistor
• SIM card slot, compatible with both normal SIM card and NB-IoT specific card
• 2x LED indicators, easy to monitor the working status
• Baudrate: 300bps~3686400bps (115200bps by default)
• Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)
• Supports SIM application toolkit: SAT Class 3, GSM 11.14 Release 98, USAT
• Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

Quick Spec

• Power Supply: 5V
• Operating Voltage: 5V / 3.3V (3.3V by default)
• Sleep Mode Current: 1.2mA (@DRX=2.56s)
• Power Save Mode Current: 9uA
• Operating Temperature: -40 ~ +85°C
• Storage Temperature: -45 ~ +90°C
• NB-IoT Frequency Bands: B1, B2, B3, B4, B5, B8, B12, B13, B17, B18, B19, B20, B25, B26, B28
• Cat-M Frequency Bands: B1, B2, B3, B4, B5, B8, B12, B13, B17, B18, B19, B20, B25, B26, B28, B39
• GPRS/EDGE Frequency Bands: 850, 900, 1800, 1900MHz
• Satellite Systems: GPS, BeiDou, GLONASS
• Dimensions: 30.2 x 65mm

Dimensions

Board Layout

1. SIM7000G
2. SPX29302 power chip
3. RT9193-33 power chip
4. Raspberry Pi GPIO header: for connecting with Raspberry Pi
5. USB interface: for testing AT Commands, getting GPS positioning data, etc.
6. SIM7000G control interface: for connecting with host boards like Arduino/STM32
7. SIM card slot: supports 1.8V/3V SIM card
8. GNSS antenna connector
9. LTE antenna connector
10. Network status indicator
11. Power indicator
12. Operating voltage selection jumper: configured via 0Ω resistor jumper
• A: set operating voltage as 5V
• B: set operating voltage as 3.3V (default)
13. DTR configuration jumper: configured via 0Ω resistor jumper
• A: DTR is controlled by the Raspberry Pi P26 pin
• B: NC (default)
14. PWR configuration jumper: configured via 0Ω resistor jumper
• A: startup/shutdown by the Raspberry Pi P4 pin
• B: auto startup on power-up (default)

Pinout

Resources

• Product Page
• Product Wiki
• User Manual
• SIM7000 Driver
• SIM7000 Series_AT Command Manual V1.05
• Source Code

Shipping List

• 1 x Wave SIM7000G Pi HAT
• 1 x GSM Antenna
• 1 x GPS External Antenna
• 1 x USB-A to Micro-B cable
• 1 x Standoffs pack