Converter 4-20mA to 0-10V VIN 7-36V

  • Brand: Generic
  • Product Code: XY-ITOV
  • Stock

    Warehouse Stock Status Location
    Centurion In Stock UL211
    Stellenbosch In Stock 935
  • R148.00 (price excl. VAT)


Converter 4-20mA to 0-10V VIN 7-36V

In the process of circuit signal transmission, the voltage signal will increase with the transmission distance becomes weak, the use of current transmission can avoid the signal weakening. This module is used for the end of the current signal transmission, the signal into a voltage signal for single-chip detection. Current input supports 4-20Ma, 0-20mA, voltage output supports 0-3.3V 0-5V 0-10V. The board is configured for the desired output voltage range by jumpers.

Quick Spec

  • Power Supply: DC 7~36V (if the output needs to be 10V, the input must be over 12V)
  • Reverse Polarity Protection
  • When the current input is at minimum (0mA or 4mA), adjust the Zero potentiometer to make the voltage output to be the minimum value (0.0V or others)
  • When the current input is at maximum (20mA), adjust the Span potentiometer to make the voltage output to be the maximum value (3.3V or 5V or 10V; the output can be as low as 2.5V when the current input is within 4 -20mA)

Please Note: After power on, the D2 indicator should be on. Otherwise, please check the wiring

Board Layout

XY-ITOV-001

Jumper Configuration

ON: jumper cap buckles on the two jumper pins - jumper shorted
OFF: two jumper pins without the jumper cap - jumper removed



  Range, Volt     J1, Jumper 1-2     J1, Jumper 3-4  
  0 - 2.5     ON     ON  
  0 - 3.3     Off     Off  
  0 - 5.0     ON     ON  
  0 - 10.0     ON     Off  


To fine-tune the 4..20 mA current to voltage converter, you need to select the values ​​of two potentiometers: ZERO and SPAN, corresponding to the zero and maximum current values ​​at the input. Claim potentiometers with a wide step.

XY-ITOV-004

  • At the minimum input current (0 mA or 4 mA), turn the ZERO potentiometer to set the desired output voltage corresponding to the set zero current. Clockwise rotation increases output voltage.
  • It is not recommend setting 0 Volts with a minimum current of 4 mA, because in this case the microcontroller will not be able to determine if the cable to the sensor is broken or it really shows the minimum values.
  • At a maximum current of 20 mA, by rotating the variable resistance SPAN, the maximum value in the range determined by jumpers is selected. Clockwise rotation increases output voltage.

Shipping List

  • 1 X Converter 4-20mA to 0-10V VIN 7-36V


Related Products

Signal Convert In 0-5V Out 4-20mA

Signal Convert In 0-5V Out 4-20mA

Signal Convert In 0-5V Out 4-20mA The SC06 is a linear conversion module, it is used to convert a 0-5V measuremnet input signal to a 4-20mA output loop signal. Quick Spec Working Voltage:..

R235.00

Signal Convert In 0-5K Out 0-5V

Signal Convert In 0-5K Out 0-5V

Signal Convert In 0-5K Out 0-5V The SC09 is a potentiometer resistance to voltage linear transformation transmitter remote data acquisition module. The board takes 0-5000 Ohm and gives a 0-5V/0-10V o..

R229.00

Signal Convert In = PT100 Out = 0-5V

Signal Convert In = PT100 Out = 0-5V

Signal Convert In = PT100 Out = 0-5V This is a linear conversion module with cold junction compensation. The chip converts the input thermocouple signal into temperature (voltage signal) output throu..

R228.00

Signal Convert In 4-20mA Out 0-5V

Signal Convert In 4-20mA Out 0-5V

Signal Convert In 4-20mA Out 0-5V This is a voltage to current module linear transmitter board for electronics equipment control. Quick Spec Operating Voltage: 9V ~ 24V Input Current: ..

R239.00

Tags: converter, 4-20ma, 10v, 36v, signal, convert

Also Bought

Breakout DB9 Female - 3 Terminal

Breakout DB9 Female - 3 Terminal

Breakout DB9 Female - 3 Terminal This is a DB9 DE9 D-SUB Female Adapter 3 Pin Signals Terminal Breakout Board RS232. It is DB9 Female(Screw) to 3Pin ( RXD TXD GND). Adapter used for communication d..

R25.00

4 Channel - Logic Level Converter Bi-Directional

4 Channel - Logic Level Converter Bi-Directional

Logic Level Converter Bi-Directional - Works with 5V / 3.3V / 2.8V / 1.8V If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. This  bi-directiona..

R35.00

I2C interface for LCD

I2C interface for LCD

I2C interface for LCD  This LCD2004 is a great I2C interface for 2x16 and 4x20 LCD displays. With the limited pin resources, your project may be out of resources using normal LCD shield. With ..

R60.00

RS485 Module( TTL -> RS485)

RS485 Module( TTL -> RS485)

RS485 Module RS485 to TTL Module is for long range, high data rate error prone differential communication. Digital communications networks implementing the EIA-485 standard can be used effectively ..

R24.95

DB9 to RS232 TTL module

DB9 to RS232 TTL module

DB9 to RS232 TTL module The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will a..

R95.00

Compact Mega Pro 2560 5V 16MHz

Compact Mega Pro 2560 5V 16MHz

Compact Mega Mini Pro 2560 5V - Size 38mm x 55 mm This is compact Arduino Mega 2560. It only measures 38x55mm. We aim to keep the standard for at least 3-5years for most customers to standardize pr..

R228.00

Sigfox Wisol Starter Kit + Antenna + 1y Subscription

Sigfox Wisol Starter Kit + Antenna + 1y Subscription

Sigfox Starter Kit + Antenna + 1Y Subscription This is a SigFox Breakout board based on the Wisol SFM10R1 module which enables easy Sigfox integration in your IOT prototype (1 year subscription inc..

R489.00

DC-DC Convertor IN 3-40V 1.5A DIP (4 Pack)

DC-DC Convertor IN 3-40V 1.5A DIP (4 Pack)

DC-DC Converter IN 3-40V 1.5A DIP (4 Pack) DC to DC converter/regulator MC34063A. Has an input range of 3V to 40V, output switch current of up to 1.5 amp. Step up, step down and invert capability. ..

R20.00